important: Nuts and bolts on your bike should always be tightened to the manufacturer's specifications.

How to Use a Chain Tool to Break a Chain

How a chain tool works, and how to use it to disconnect and reconnect your bike chain.

This week we’ll learn how to break a chain using a chain tool. I’ll cover the quick release method next week.

Quick Release Links

The first thing to do is check to make sure your chain does not already have a quick release link. Do this by turning your pedals backwards and carefully watching every chain link as it goes by. A quick release link will stand out as they look different from all of the others. If you find one, you can refer to next week’s tutorial for removal and installation instructions.

The Chain Tool

If you can’t find a quick release link, then your chain probably doesn’t have one. This has traditionally been the most common type of chain, and it requires a chain tool for both removal and installation.

Turn the handle of your chain tool counter-clockwise until the pin has backed off enough so you can place one of your chain links on the outermost slot, furthest from the handle. There are two places on chain tools where you can place a chain. The outer slot is for disconnecting and re-connecting the chain, while the inner slot is for loosening chain links.

Disconnect the Chain

Now tighten the handle clockwise until the chain tool’s pin connects with the end of your chain pin. Continue tightening the handle and you’ll see the chain pin get pushed into the link and start coming out the other side. The tricky part here is to push the chain pin far enough so that it is gets about halfway through the first of the two outer chain plates. If the chain pin gets pushed all the way out of the chain there is really no way to get it back in, and you’ll be forced to shorten or replace your chain.

One way to prevent this is to pay careful attention to how easy the handle turns as you push the pin through. When you get close to the end, you’ll feel resistance and the handle will become a slight bit harder to turn. As soon as you feel this, stop tightening the handle, and then give it another half a turn. This is usually the perfect spot to disconnect the chain. When you take the chain tool off, you’ll notice the chain is still barely held together, but can be easily disconnected by twisting and pulling the chain.

Reconnect the Chain

Notice how a tiny bit of the pin is still poking out of the inner side of the outermost plate. This is perfect, as it will help us re-install the chain. Twist and push the links back together until the chain pin clicks back into the inner link, once again holding the chain together.

Now back off the chain tool’s handle and place the chain back onto the same outer slot of the chain tool. This time position it so the protruding chain pin faces inward toward the chain tool’s pin. Now tighten the handle until the tool pin starts pushing the chain pin back through the link. Continue tightening until a tiny bit of the link pokes through the other side. Now take a look at both sides of the link… the chain pin should stick out roughly the same amount on either side.

Loosen the Chain Link

The process of re-connecting the chain caused the chain links to compress together, making a stiff link. To fix this, we use the inner slot on the chain tool. Back off the chain tool all of the way so that you can place the freshly connected link into the inner slot. Now tighten the chain tool’s pin until it connects with the chain pin and tighten it just barely, about a quarter of a turn. This usually loosens the chain link plates enough. Remove the chain from the tool and check to make sure the link is loose. If it’s still tight, try loosening it with the chain tool another quarter of a turn.

Related Links

Recommended Tools

Categories

Discuss this topic in the Bicycle Repairs and Mechanics Forum

I'm slowly eliminated all LBSes in my area as options for servicing, LOL. The latest one has been struck off my list after watching, pained, their approach to removing the axle end caps from a hub with cartridge bearings. Suffice to say, I finally ordered a blind bearing puller kit and a bearing press kit. If you want something done properly, you have to do it yourself! Have you bought any nic...

Read more

Hi Ive joined to specifically ask about a problem which may have been covered before Im sure. My right pedal broke so I had to replace it. Then had issues getting the new pedal to go on straight so I was riding with it slightly at a bend. But then it just came loose and fell off. Problem is now the thread seems busted and the pedal just slots in with no screwing needed because the hole is enlar...

Read more

Trek domane tyre

Latest post 4 days ago

Hi I have a trek domane 2.3, and I have changed the rear tyre to 28 (it was 25 originally) The tyre rubs with the brake arm (v brake), I fear it doesn’t seem to be compatible Is there any way to adjust the position of the brake arm? I just need it to ne around 2mm higher Thanks...

Read more

Modern rims crack at spoke holes

Latest post 4 days ago

Recently, I was in one of the local bike shops. Someone had brought a bike back to have the back wheel re-trued. There were actually cracks in the rim, originating from the spoke holes. I have had the same problem with my bike. In past decades you could buy a bike, and the wheels were strong. With modern rims, the aluminum is getting thinner and thinner. Now the rims crack. With heavy riders, a...

Read more

Cup and cone hubs have long been considered simple, durable, easily maintained, and reliable. Having messed around with a couple of older hubs tonight, I ended up looking at my sealed-bearing hubs with increased fondness. I'm wondering what other people think. Should we old farts just accept that modern hubs with cartridge bearings are the way forward?...

Read more

Falling back

Latest post 4 days ago

In December of 2009 I had a first generation carbon fiber fork break on my road bike and it dropped me right on my forehead. This gave me a very serious concussion and both ER doctors and most neurologists do not take them serious. So it took about two years of my slowly dying since I couldn't even remember to eat before my Cop friend took me to a proper neurologist who diagnosed it as a concussio...

Read more

Derailluer Hanger Alignment Tool

Latest post 4 days ago

I cannot express enough about the importance of this tool when having to deal with multi speed bicycles. I have been in the bicycle biz in one fashion or the other for over 30 years. Have sold many new bicycles and 90% have been out of wack fresh from the box. With used bikes crossing your path you should just expect it to be bad. And never string new cables without checking the hanger first, ever...

Read more

Hey guys, First post here. I've tried searching, but I don't know what you call this. I have a vintage Schwinn Passage that I picked up a few months ago. At first it worked well, but recently it's been giving me trouble. When I shift, the chain pops into the higher (larger) gear, but then sits on top of the chain ring. What ends up happening is that the chainring will keep turning, and eve...

Read more

Went to fix the slow leak on my gravel bike's rear tyre. Found the culprit: a small cut near the middle of the tyre. The good news is it gave me an excuse to order a pair of Panaracer 43c semi-slick GravelKings (most of my local rides are more road-focused) to try out. Meanwhile, I was considering ye olde vulcanised patch repair to the inside of the tyre and superglue to the outside, but I'm thi...

Read more

I shipped my Dawes Super Galaxy home and have just had an unfortunate experience of not being able to re-attach my left Shimano M324 pedal. It looks threaded, but I still have hopes as I think it's only the top couple of rings on the inside. [attachment=5341] From what I can tell the pedal thread is fine. I know there are tools out there to fix a thread. I'm hoping that mine is not so bad that...

Read more

I bought this Vilano Hybrid in 2020 as my “old person’s Chinese Cheapie”. It was - (and is) - FAR from equaling the “serious” bikes that I owned back in the 1990’s. The first Trek I had was a gorgeous blue road bike - worthy of all the gawkers it inspired. My Klein Pro Race MTB was the finest all-round “terrain-chewing animal” I ever mounted. It never failed. It never said...

Read more

Crankarm for Diamondback

Latest post 3 weeks ago

Will a FC-CT93 fit a FC-TY40 crank arm...

Read more

I am heavier than many cyclists. I ride longer distances then many cyclists. A lot of my riding is on rough tracks. While riding my 29 inch mountain bike, spokes broke in the back wheel. https://forums.bikeride.com/thread-8373.html I replaced them with 3 mm spokes. Not long after, cracks formed in the aluminum rim in two places. It became obvious, I could not go on repairing this wheel. I came...

Read more

New Wheel Question

Latest post 4 weeks ago

I just ordered and received new wheels for my bike. Both the old and new are TLR, but I run with tubes. On my old rim, tape is installed. So…when I ordered the new wheels, I also ordered tape. Today, when the new wheels arrived, I noticed that both included a plastic (?) rim strip. I installed the strip on both rims, which gets me to my question…. Do I also need the rim tape? I would think not...

Read more

New Wheel Question

Latest post 4 weeks ago

I just ordered and received new wheels for my bike. Both the old and new are TLR, but I run with tubes. On my old rim, tape is installed. So…when I ordered the new wheels, I also ordered tape. Today, when the new wheels arrived, I noticed that both included a plastic (?) rim strip. I installed the strip on both rims, which gets me to my question…. Do I also need the rim tape? I would think not...

Read more